Optional: Dual operation: LAN & VPN at the same time
Up until now, this wiki has been about a server set up on a cloud host, available on the public Internet. This section is aimed at a server set up in a private network like on a Raspberry Pi.
So if blocking works using eth0 but stops working for tun0, as described here, you may want to run this command pihole -a -i all, which should get the behavior you want by opening pihole-FTL up to listen on all ports. This is not recommended for cloud servers as they should not be listening on eth0.
If you want to set up your Pi-hole + OpenVPN such that you can use from both internal ((W)LAN) and external (VPN) networks, you have to apply some small changes. As an additional benefit, you will be able to reach all devices in the internal network (e.g. computers, networking-aware printers, etc.) through the VPN.
This setup assumes that your local network is in the range 192.168.2.0 (i.e. device addresses are in the range of 192.168.2.1 - 192.168.2.254). If this is not the case for you, you have to adjust the settings, accordingly, e.g.
- devices in 192.168.0.1 - 192.168.0.254 ->
route 192.168.0.0 - devices in 192.168.123.1 - 192.168.123.254 ->
route 192.168.123.0
Edit your /etc/openvpn/server/server.conf:
push "route 192.168.2.0 255.255.255.0"
push "dhcp-option DNS 192.168.2.123"
As you can see, we change the address of the DNS server to the local IP address of our Pi-hole (which is 192.168.2.123 in this example).
Afterward, we change the interface of Pi-hole to eth0 (your local network adapter instead of the VPN adapter tun0). This can conveniently be done by using pihole -r + Reconfigure.
After a restart of the OpenVPN server, all clients should be able to see all devices within your (at home) local network. This is an example running on a distant server, which is connected through the VPN and can successfully communicate with all internal devices:
me@client ~ $ ifconfig
eth0 Link encap:Ethernet HWaddr e0:xx:xx:xx:xx:xx
inet addr:134.x.x.x Bcast:134.x.x.x Mask:255.x.x.x
inet6 addr: X:X:X:X::X/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3623911 errors:0 dropped:0 overruns:0 frame:0
TX packets:2803670 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1921375471 (1.9 GB) TX bytes:1227835028 (1.2 GB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:553426 errors:0 dropped:0 overruns:0 frame:0
TX packets:553426 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1
RX bytes:113417383 (113.4 MB) TX bytes:113417383 (113.4 MB)
tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
inet addr:10.8.0.2 P-t-P:10.8.0.2 Mask:255.255.255.0
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:274676 errors:0 dropped:0 overruns:0 frame:0
TX packets:331178 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:43745313 (43.7 MB) TX bytes:43956250 (43.9 MB)
me@client ~ $ ping 192.168.2.123
PING 192.168.2.123 (192.168.2.123) 56(84) bytes of data.
64 bytes from 192.168.2.123: icmp_seq=1 ttl=64 time=18.9 ms
64 bytes from 192.168.2.123: icmp_seq=2 ttl=64 time=18.9 ms
64 bytes from 192.168.2.123: icmp_seq=3 ttl=64 time=18.9 ms
64 bytes from 192.168.2.123: icmp_seq=4 ttl=64 time=18.7 ms
64 bytes from 192.168.2.123: icmp_seq=5 ttl=64 time=18.7 ms
64 bytes from 192.168.2.123: icmp_seq=6 ttl=64 time=19.0 ms
^C
--- 192.168.2.123 ping statistics ---
6 packets transmitted, 6 received, 0% packet loss, time 5007ms
rtt min/avg/max/mdev = 18.740/18.894/19.017/0.189 ms
Important last step¶
The undocumented pihole -a -i all command is simply what runs when you choose Listen on all interfaces, permit all origins (make sure your Pi-hole is firewalled), which if you've read this far in the tutorial, you should understand that we don't want you to knowingly or unknowing set up an open resolver.
